Ripping narrow boards is not an easy task, especially for an average woodworker. Knowing how to rip narrow boards with a circular saw is enjoyable to produce precise and friendly cuttings. The primary tool to use here is the circular saw, but that does not guarantee the task’s success. You need some knowledge for the smooth running of the ripping process.
Let not the task worry you again because this article will equip you with necessary ideas on how you can rip your narrow boards right at home using a circular saw. So, if you are a DIYer, this report will give you a great company.
Table of Contents
- 1 Step by step guide on how to rip narrow boards with a circular saw
- 1.1 Step one: Choosing an appropriate platform
- 1.2 Step two: Clamping the sole of the circular to the platform or slab
- 1.3 Step three: Making a reference or guideline cut to twist the saw
- 1.4 Step four: Adjust the saw blade carefully to be parallel to the surface of the slab
- 1.5 Step five: adjusting the height of the saw blade
- 1.6 Step six: Readjusting of parallel
- 1.7 Step seven: Start to rip the narrow board
- 2 Frequently asked questions
- 3 Conclusion
Step by step guide on how to rip narrow boards with a circular saw
Before you do anything, there is a need to gather all the necessary materials and equipment. These items will try to make work easier. Some of them include;
A small circular saw a saw truck, sharp circular blade, sawhorses/foam boards/work table, clamp/8d nails, wood pencil, an angle, or measuring tape.
Now that you have the above tools let us now follow the following steps to perfect rip narrow boards with a circular saw. This process is not that complicated; you only need to go through some steps.
Step one: Choosing an appropriate platform
Take a straight and long piece of wood, or you can use a slab as your platform. You will need many tables depending on the wood’s height, but I would prefer more extended slabs. They will work for you better.
Besides, the platform must not be thinner than the board you plan to handle. More so, ensure that the slab is higher than your workpiece because a circular saw will be running on the same platform.
Step two: Clamping the sole of the circular to the platform or slab
Clamp the sole of the circular to the slab at 2 points. If it fails to hold the saw sole tightly, apply some wood bits to ensure it is appropriately controlled. Remember, working with a friendly workpiece will enhance precise results.
Step three: Making a reference or guideline cut to twist the saw
It would help if you were much careful under this step because you will have to identify the front part of your circular saw. Of course, the front side is always the part you push the circular saw in. So, feed a testing piece of wood slowly and carefully into the circular saw blade to create a reference cut.
The next thing will be to measure the reference cut you get; if the thickness is not your desire, you need to move and push the front part of your saw correspondingly.
Step four: Adjust the saw blade carefully to be parallel to the surface of the slab
Here, the blade of the circular saw should be correctly parallel to the platform’s face. If you fail to adjust it precisely, prepare to experience warping while the cutting process is on. Besides, this strain will interfere with the circular saw motor and end up destroying the workpiece. Sometimes the stain may also shatter the saw blade.
Use another testing piece of wood and push it carefully into the saw blade from the machine’s front side. Turn the testing wood over; you will see the guideline cut from the front part will be the underside.
After that, you have to feed the wood into the machine but, this time, it should from the back of the saw. To succeed in another reference cut, you need to push the blade guard from the way. Remember, these two cuts should connect at the same place with a perfect joint.
Sometimes the cuts may fail to meet correctly, down worry, adjust the saw blade. Doing so is very simple as you only need to loosen your clamp at the backside of the machine and adjust it correspondingly.
Moreover, if these two points perfectly join at the same place, know that the saw blade is parallel, and you are free to move to the next step.
Step five: adjusting the height of the saw blade
When the workpiece is on the top side of the saw blade, there is a need to adjust the unit’s blade’s depth. It would be best if you dropped the saw’s edge to the surface of the table. Also, you may slide a piece of paper beneath the blade. What you need to be sure of is that the sheet of paper comfortably passes beneath the edge.
Step six: Readjusting of parallel
If the machine’s body is narrow to saw sole, there is a need to readjust it again. You should ensure the saw blade stands perpendicularly on the table. More so, you may decide to push a wedge, positioning it between the motor casing and the sole.
Step seven: Start to rip the narrow board
After everything is in place, it is now time to rip the board. Your health comes first; wear safety glasses, dust mask, and ear protectors. Remember, this method is the best one that can allow you to rip up to boards of ¾ inches.
Frequently asked questions
What happens when you fail to adjust the saw blade correctly?
If you fail to adjust the saw blade correctly, prepare to experience warping while the cutting process is on. Besides, this strain will interfere with the circular saw motor and end up destroying the workpiece. Sometimes the stain may also shatter the saw blade.
What is the advantage of clamping when ripping narrow boards?
The clamp is useful for holding the sole of the circular saw tightly while ripping.
I hope you benefit from the above step-by-step guide on rip narrow boards with a circular saw. The report provides you with the steps that are precise and simple to understand while ripping little boards. When you follow the steps carefully, you can rip boards of up to ¾ inches.
More so, it would help if you were careful when adjusting the saw blade to make accurate reference cuts. Besides, you need to inspect the unit to make sure it is in good working condition. Don’t also forget to consider safety measures; your health comes first. Wear a dust mask, safety glasses, and ear protectors.